Navigation* - specify destination

Specify destination in the navigation system.

Each time a destination is specified it is possible to save it as "stored location" or "home", which is then easily accessible when a destination shall be specified. The navigation system gives guidance to a destination, and it is possible to add four waypoints in the itinerary. For many destinations, the navigation system can also give further information with the Information menu option.

With the car connected to the Internet it is possible to use the app "Send to Car" to send map destinations from a browser and via Volvo On Call* app* to the navigation system, see support.volvocars.com.

To access the following alternative methods for specifying destinations, in the normal view for the navigation source, press OK/MENU and select Set destination.

P3-1346-NAV-Melco Meny Adress-Hem

Specify destination with home

Note that the destination must have been saved previously to be specified.
In the normal view for the navigation source, press OK/MENU and select Set destination → Home.
Guidance starts.

Specify destination with address

It is sufficient to only enter a city/town in order to obtain an itinerary with guidance - it guides to the centre of the city/town.

 Note

The definition of city or area may vary from country to country and even within the same country. In some cases, it refers to a municipality and in others it refers to a district.
In the normal view for the navigation source, press OK/MENU and select Set destination → Address.

Fill in one or more of the following search options:

  • Country:
  • City:
  • Street:
  • Number:
  • Junction:

If more information about the destination is required, select Information and then the required information:

  • Map - Shows where on the map the location can be found - sometimes with additional information.
  • Call number1 - Calls the facility if a telephone number is given.
  • Online info.1 - Supplementary information is downloaded from the Internet.
To store the address in the memory, select Save and then as Stored location or as Home.

Specify as intermediate destination or as single destination:

  • Add as waypoint - adds the address to the itinerary.
  • Set single destination - Deletes any previous destination in the itinerary and starts guidance to the current destination.

Specify destination with point of interest (POI)

POI (Point of Interest) also denominated as point of interest and facility.

The map database contains a large number of searchable POI2 options which can be specified as destinations.

In the normal view for the navigation source, press OK/MENU and select Set destination → Point of interest (POI).

Search for point of interest using the following:

  • By name - leads directly to the character wheel and refers to searching of POI options with their proper name, e.g. "Peppes Bodega". The search area is the whole of the current map area, e.g. EUROPE, see Maps - content.
  • By category - enables limited searching of POI options - select to enter their category (e.g. bank/hotel/museum), proper name, country and/or city/town.
  • Near the car - refers to searching of POI options around the car's current position.
  • Along the route - refers to searching of POI options along the set itinerary.
  • Near the destination - refers to searching of POI options in the vicinity of the destination.
  • Around point on map - refers to searching of POI options with the scroll function's crosshair - see scroll menu.

If more information about the destination is required, select Information and then the required information.

To store the address in the memory, select Save and then as Stored location or as Home.

Specify as intermediate destination or as single destination:

  • Add as waypoint - adds the address to the itinerary.
  • Set single destination - Deletes any previous destination in the itinerary and starts guidance to the current destination.

Specify destination using previous destination

In the normal view for the navigation source, press OK/MENU and select Set destination → Previous destination.

Select a destination in the list.

If more information about the destination is required, select Information and then the required information.

Here it is also possible to delete a destination, select Delete or Delete all.

Specify as intermediate destination or as single destination:

  • Add as waypoint - adds the address to the itinerary.
  • Set single destination - Deletes any previous destination in the itinerary and starts guidance to the current destination.

Specify destination using previously stored location

Collected here are the destinations stored with the menu option Save → Stored location.

Note that the destination must have been saved previously.
In the normal view for the navigation source, press OK/MENU and select Set destination → Stored location.

Open saved destination:

  • Routes - e.g. recorded section of road.
  • Other - e.g. saved locations.

If more information about the destination is required, select Information and then the required information.

Here it is also possible to edit or delete a saved destination, select Edit, Delete or Delete all.

Specify as intermediate destination or as single destination:

  • Add as waypoint - adds the address to the itinerary.
  • Set single destination - Deletes any previous destination in the itinerary and starts guidance to the current destination.

Specify destination with Internet search

Requires connection to Internet.
In the normal view for the navigation source, press OK/MENU and select Set destination → Internet search.
Follow the on-screen instructions.

Specify destination with postcode

In the normal view for the navigation source, press OK/MENU and select Set destination → Postcode.

Type in the postcode, and country if required.

If more information about the destination is required, select Information and then the required information.

To store the destination in the memory, select Save and then as Stored location or as Home.

Specify as intermediate destination or as single destination:

  • Add as waypoint - adds the address to the itinerary.
  • Set single destination - Deletes any previous destination in the itinerary and starts guidance to the current destination.

Specify destination with latitude and longitude

P3-1346-NAV-Melco Meny Adress-LatLon-2
In the normal view for the navigation source, press OK/MENU and select Set destination → Latitude and longitude.

First decide which method the GPS coordinates should be specified with, select Format::

  • DD°MM'SS'' - position with Degrees, Minutes and Seconds.
  • Decimal - position with Decimals.

Type in the position.

If more information about the destination is required, select Information and then the required information.

To store the address in the memory, select Save and then as Stored location or as Home.

Specify as intermediate destination or as single destination:

  • Add as waypoint - adds the address to the itinerary.
  • Set single destination - Deletes any previous destination in the itinerary and starts guidance to the current destination.

Specify destination using point on map

P3-1346-NAV-Melco Meny Sökning via punkt på karta-2
Cursor position specified with GPS coordinates. To change to showing name, select Settings → Map options → Position information.
In the normal view for the navigation source, press OK/MENU and select Set destination → Select point on map.
Locate and specify desired point on map using the crosshair, see section Menus.
To store the address in the memory, press OK/MENU and select Save and then as Stored location or as Home.
The destination is stored as a symbol/icon on the map if the Stored location on map function is selected, see section Map options.

Specify as intermediate destination or as single destination:

  • Add as waypoint - adds the address to the itinerary.
  • Set single destination - Deletes any previous destination in the itinerary and starts guidance to the current destination.

Specify destination with travel guide

Search with travel guide (Travel guide) means that prepared suggestions are available to choose from with varying themes, e.g. restaurants, scenic roads or sights and landmarks.

A travel guide is stored in a USB memory, which must be fitted in the car's USB connector in the tunnel console's rear storage compartment.

In the normal view for the navigation source, press OK/MENU and select Set destination → Travel guide.

If the menu option is not visible on the screen then there are no suggestions in the area the car is currently in, or a USB device is not connected.

Select travel guide via one of the following categories:

  • Restaurants
  • Tourist attractions
  • Hotels
  • Tourist routes
  • Other

If available in the travel guide, it is possible to view details and images, as well as to play back audio, select:

  • Details
  • Photos
  • Play audio
Set Start guidance.

Related documents